Paper Backed Style CG-400
Our premium wood veneer is available in more than 90 species from A - Z (Ash to Zebra) with 10-mil paper backing. This makes the sheets ideal for flat surfaces or a soft radius. Curvwood CG paper backed is suitable for use with contact adhesive and can be applied to almost any type of substrate. Curvwood CG 10 mil is readily available in a large variety of species and is the most economical type of wood veneer in the Curvwood line.



  • Paper-backed veneer provides stability & flexibility.

  • Helps to minimize splitting, grain-raise & some glue seepage.

  • Custom matching of veneer sheets to specification is available.

  • 10-mil paper backings are available.

  • Sizes range: 4’ x 8’, 4’ x 10’, 4’ x 12’, also 8’ x 4’, 10’ x 4’, 5’ x 8’, 5’ x 10’, 5’ x 12’.

  • 90 + wood veneers in Domestic and Exotics species are available for you requirements.

  • Tenderized paper-backed veneer will bend to a soft 1” radius, (varies with specie).

  • High grading standards and stringent quality standards.

  • Variations to be expected from sheet to sheet & lot to lot.

  • Book or Balance matching available at addition charge, subject to specie.


Standard sheet sizes with 10-mil paper-back: 4’ x 8’ long and 4’ x 10’ sheets.

Technical Specifications PDF: Curvwood Paper-Backed CG-400

E-mail or fax us for a quote on 20 & 30 mil paper for your special project. Quote Request PDF

Quick Ship CG-400 10 mil (Running Book Matched) unless otherwise noted.

1 Sheet customers add $30.00 NET (includes Box) to the 2 sheet price, then only +UPS.

OK to mix specie and sheet quantity for lowest sheet price, for 1 shipment.

Quick Ship CG-400 10 mil Paper Back 

Wood Veneer

Price per Sheet*

4’ x 8’




10 +


Ash, White F/C

$ $59.75


Birch, White - Rotary Spliced

$ 54.80



$ 55.85


Cherry, F/C Premium

$ 64.00


Mahogany, F/C Competitive African (Khaya)

$ 55.00


Mahogany, F/C Premium African (Khaya)

$ 61.50



$ 53.40


Maple Quarters

$ 82.75


Maple, White F/C Premium

$ 58.70


Oak, Red F/C

$ 50.15


Oak, Red F/C Premium

$ 52.00


Oak, White F/C

$ 55.85


Oak, White F/C Premium

$ 59.40


Pine, Knotty - Plank Matched

$ 56.75


Sapele, Qtr.

$ 59.40


Teak F/C



Walnut, F/C

$ 60.25


Walnut, F/C Premium

$ 68.75


* All prices subject to change without notice due to veneer
  market fluctuations.
Please call, e-mail, or fax for Freight charges.
* Since we have no control over the end use of Paper Backed veneer, the
  job site conditions, the skill of the installer, and the quality of finishing,
  NO warranty is expressed or implied. 


Please call for lead times and minimums on all other species not listed above.

Click Here For Sample Information

Curvwood Sample Library

Ordering Information



Paper-Backed, Natural WoodEdge, Duraback

Sheet Veneer Products - Please Review before ordering.


General Application Considerations / Guidelines

Note: A skilled wood worker should only apply veneer sheet products.

Beware: NOT a RETAIL product, no installation instructions.



Materials should be properly conditioned before they are used. The standard recommendation is that both the veneer and substrate should be stored in the same environment for 5 days to ensure their moisture content is in equilibrium. Extreme temperature/humidity fluctuations will affect both the veneer and substrate. High humidity levels will cause veneer to expand/buckle, while extremely dry conditions will cause veneer to shrink. Both the veneer and substrate should be free of paint, grease, dirt, dust, oil, or any other foreign matter. Substrate surfaces must be sanded with 80 grit sandpaper and entire area dusted clean. Good bonds depend upon smooth, clean, dry surfaces.



Solvent based adhesives work best with veneer products. Water based products should be avoided when possible. The adhesive should be applied uniformly to both the substrate and veneer. 100% glue coverage is recommended. This is especially critical to the edges and areas where veneer sheets butt together. Any areas void of glue adhesive can bubble. If the substrate is porous and absorbs adhesive, a second coat is required. The veneer back should be coated also.

Follow the glue manufacturer's recommendation on open time before bonding the veneer to the substrate.

Keep in mind the open time is affected by humidity and temperature. Adhesives which contain higher solid contents perform better. Adhesives should always be stirred or agitated before use. This is particularly necessary with large containers. See manufacturer's recommendations.

The Only Exception to the non-use of water-based glues is with our DuraBack™ Resin-Backed veneer, which is recommended for use with both water and solvent-based adhesives.


*Potential Trouble Areas*

   1. Using water based products immediately raises moisture content and can cause delamination.

   2. Too little, too much, or uneven distribution of glue can cause delamination.

   3. Bonding before adhesive solvent has evaporated or after open time has expired can cause delamination.

Not recommended for use on sheet rock or drywall



To ensure intimate contact necessary for an adequate bond, sufficient pressure should be applied over the entire area using as much pressure as possible without damaging the veneer. Platten presses and bag presses work very well. If these options are not available use a fiber knife or veneer scraper and start in the center of the veneer sheet working out. Always work in the same direction as the grain of the veneer. The edges should always be scraped twice. A standard "J" roller is not recommended due to the low pressure exerted with them.



The adhesive should dry a minimum of 48 hours before finishing. High grade petroleum based urethanes and acrylic based lacquers reduce the risk of veneer checking. These finishes provide a good moisture barrier. Always seal the back of panels if raw or unsealed. Follow the recommendations of the finish manufacturer.

Note: Seller warrants merchandise to be free from defects in material and workmanship. Customer assumes all responsibility and liability for use and results of materials purchased.



If your budget requires a lower price than shown, please
call us at 800-527-9014 or for a quote.



Corporate Home    •   Curvwood Home   •    CurvTambour Home    •    Wood Wallcovering    •    10 mil Paper Backed Wood Veneer

Natural WoodEdge Wood-On-Wood Veneer     •     Curv2Ply Wood Veneer     •     DuraBack Resin-Backed Veneer

PSA Peel & Stick Backed Wood Veneer     •     Door Saver - Door Refacing Veneer     •     Wood Grain Vinyl

Veneer Scraper For Veneer Installation     •     Curvwood Wood Veneer Sample Library     •     Curvwood Ordering Information

Red Oak Solid Wood Tambour     •     Solid Wood Tambour - Various Species     •     Wood Veneer Tambour

Paint-Grade Solid Wood Tambour     •     Paint-Grade Hardboard Tambour     •     Paint-Grade Fiberboard Tambour

Decorative Laminate Tambour     •     Decorative Metal Tambour     •     Clothback Veneer CurvTambour     •     Clothback Solid Wood CurvTambour

Doors - Solid Wood     •     Doors - Wood Veneer with Leadrails     •     Doors Solid-Look Veneer Tambour     •     Curved Mirror

CurvTambour Sample Library     •     CurvTambour Ordering Information     •     Curvwood & CurvTambour FAQs     •     Contact Us

Call Us Toll Free at 800-527-9014 M - F (8:30 AM to 5:00 PM CT)
FAX 214.327.4101

Curvwood is a registered trademark and CurvCork is a trademark of WI, Wallcovering Industries, Inc., and WI Contract are corporate divisions of WI.
ฉCopyright 2001-2015 Wallcovering Industries, Inc.  All rights reserved